DG's Hardware board

Code: Select all

[    0.000000] Linux version 4.14.167 (openwrt@LD861) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10860-a3ffeb413b)) #0 SMP Wed Jan 29 16:05:35 2020
[    0.000000] SoC: xRX200 rev 1.1
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019555 (MIPS 34Kc)
[    0.000000] MIPS: machine is ZyXEL P-2812HNU-F1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Detected 1 available secondary CPU(s)
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat 8066b6a0, node_mem_map 8100bfc0
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] random: get_random_bytes called from start_kernel+0x90/0x4a4 with crng_init=0
[    0.000000] percpu: Embedded 14 pages/cpu s25936 r8192 d23216 u57344
[    0.000000] pcpu-alloc: s25936 r8192 d23216 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00044860
[    0.000000] Readback ErrCtl register=00044860
[    0.000000] Memory: 121628K/131072K available (5028K kernel code, 187K rwdata, 1352K rodata, 1288K init, 228K bss, 9444K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 500MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
[    0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
[    0.007906] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.046048] pid_max: default: 32768 minimum: 301
[    0.050964] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.057475] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.066915] Hierarchical SRCU implementation.
[    0.072444] smp: Bringing up secondary CPUs ...
[    0.077945] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.077959] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.078112] CPU1 revision is: 00019555 (MIPS 34Kc)
[    0.109142] Synchronize counters for CPU 1: done.
[    0.133453] smp: Brought up 1 node, 2 CPUs
[    0.142683] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.152355] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.158634] pinctrl core: initialized pinctrl subsystem
[    0.165207] NET: Registered protocol family 16
[    0.181392] pinctrl-xway 1e100b10.pinmux: Init done
[    0.188116] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.200198] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.212991] PCI host bridge /fpi@10000000/pci@e105400 ranges:
[    0.218673]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.223920]   IO 0x000000001ae00000..0x000000001affffff
[    0.253281] gpio-stp-xway 1e100bb0.stp: Init done
[    0.260292] usbcore: registered new interface driver usbfs
[    0.265976] usbcore: registered new interface driver hub
[    0.271390] usbcore: registered new device driver usb
[    0.277049] PCI host bridge to bus 0000:00
[    0.281092] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.287995] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]
[    0.294960] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.301790] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.309870] pci 0000:00:0e.0: [1814:3062] type 00 class 0x028000
[    0.309927] pci 0000:00:0e.0: reg 0x10: [mem 0xffff0000-0xffffffff]
[    0.310381] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.310440] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[    0.319143] clocksource: Switched to clocksource MIPS
[    0.325619] NET: Registered protocol family 2
[    0.331550] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.338444] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.344854] TCP: Hash tables configured (established 1024 bind 1024)
[    0.351461] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.357237] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.363851] NET: Registered protocol family 1
[    0.368179] PCI: CLS 0 bytes, default 32
[    0.368943] gptu: totally 6 16-bit timers/counters
[    0.373896] gptu: misc_register on minor 63
[    0.378070] gptu: succeeded to request irq 126
[    0.382624] gptu: succeeded to request irq 127
[    0.387061] gptu: succeeded to request irq 128
[    0.391571] gptu: succeeded to request irq 129
[    0.396102] gptu: succeeded to request irq 130
[    0.400598] gptu: succeeded to request irq 131
[    0.405314] No VPEs reserved for AP/SP, not initialize VPE loader
[    0.405314] Pass maxvpes=<n> argument as kernel argument
[    0.416701] No TCs reserved for AP/SP, not initializing RTLX.
[    0.416701] Pass maxtcs=<n> argument as kernel argument
[    0.429492] Crashlog allocated RAM at address 0x3f00000
[    0.435063] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.453706] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.459515] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.471486] random: fast init done
[    0.478383] io scheduler noop registered
[    0.482243] io scheduler deadline registered (default)
[    0.491831] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.500813] console [ttyLTQ0] enabled
[    0.508083] bootconsole [early0] disabled
[    0.519781] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[    0.524705] nand: Samsung NAND 128MiB 3,3V 8-bit
[    0.529312] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.536969] Scanning device for bad blocks
[    0.562934] Bad eraseblock 242 at 0x000001e40000
[    0.577561] Bad eraseblock 370 at 0x000002e40000
[    0.590520] Bad eraseblock 478 at 0x000003bc0000
[    0.632458] Bad eraseblock 909 at 0x0000071a0000
[    0.645969] 4 fixed-partitions partitions found on MTD device 10000000.nand
[    0.651529] Creating 4 MTD partitions on "10000000.nand":
[    0.656954] 0x000000000000-0x000000040000 : "uboot"
[    0.663664] 0x000000040000-0x000000060000 : "uboot-env"
[    0.669151] 0x000000060000-0x000000360000 : "kernel"
[    0.674454] 0x000000360000-0x000008000000 : "ubi"
[    0.685176] libphy: Fixed MDIO Bus: probed
[    0.692164] wdt 1f8803f0.watchdog: Init done
[    0.703267] NET: Registered protocol family 10
[    0.709678] Segment Routing with IPv6
[    0.712129] NET: Registered protocol family 17
[    0.716485] 8021q: 802.1Q VLAN Support v1.8
[    0.830651] libphy: lantiq,xrx200-mdio: probed
[    0.911232] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.3 0:00: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.3] (mii_bus:phy_addr=0:00, irq=POLL)
[    0.995208] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.3 0:01: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.3] (mii_bus:phy_addr=0:01, irq=POLL)
[    1.079194] Intel XWAY PHY11G (xRX v1.1 integrated) 0:11: attached PHY driver [Intel XWAY PHY11G (xRX v1.1 integrated)] (mii_bus:phy_addr=0:11, irq=POLL)
[    1.163193] Intel XWAY PHY11G (xRX v1.1 integrated) 0:13: attached PHY driver [Intel XWAY PHY11G (xRX v1.1 integrated)] (mii_bus:phy_addr=0:13, irq=POLL)
[    1.247209] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.3 0:05: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.3] (mii_bus:phy_addr=0:05, irq=POLL)
[    1.262678] UBI: auto-attach mtd3
[    1.264575] ubi0: attaching mtd3
[    1.435606] ubi0: scanning is finished
[    1.451909] ubi0: attached mtd3 (name "ubi", size 124 MiB)
[    1.456044] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    1.462873] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    1.469594] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[    1.476362] ubi0: good PEBs: 993, bad PEBs: 4, corrupted PEBs: 0
[    1.482390] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    1.489596] ubi0: max/mean erase counter: 22/15, WL threshold: 4096, image sequence number: 382787294
[    1.498829] ubi0: available PEBs: 0, total reserved PEBs: 993, PEBs reserved for bad PEB handling: 16
[    1.508142] ubi0: background thread "ubi_bgt0d" started, PID 421
[    1.513956] block ubiblock0_0: created from ubi0:0(rootfs)
[    1.519625] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    1.526956] USB_VBUS: disabling
[    1.538837] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    1.548581] Freeing unused kernel memory: 1288K
[    1.551716] This architecture does not have kernel memory protection.
[    2.322123] init: Console is alive
[    2.324564] init: - watchdog -
[    3.314843] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[    4.393996] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.548197] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.562620] SCSI subsystem initialized
[    4.570286] ehci-platform: EHCI generic platform driver
[    4.577519] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.583785] ohci-platform: OHCI generic platform driver
[    4.590371] uhci_hcd: USB Universal Host Controller Interface driver
[    4.601451] dwc2 1e101000.usb: 1e101000.usb supply vusb_d not found, using dummy regulator
[    4.608502] dwc2 1e101000.usb: 1e101000.usb supply vusb_a not found, using dummy regulator
[    4.617041] dwc2 1e101000.usb: dwc2_core_reset() HANG! AHB Idle GRSTCTL=0
[    4.827012] dwc2 1e101000.usb: DWC OTG Controller
[    4.830342] dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
[    4.837434] dwc2 1e101000.usb: irq 62, io mem 0x1e101000
[    4.844234] hub 1-0:1.0: USB hub found
[    4.846765] hub 1-0:1.0: 1 port detected
[    4.851910] dwc2 1e106000.usb: 1e106000.usb supply vusb_d not found, using dummy regulator
[    4.859037] dwc2 1e106000.usb: 1e106000.usb supply vusb_a not found, using dummy regulator
[    4.867529] dwc2 1e106000.usb: dwc2_core_reset() HANG! AHB Idle GRSTCTL=0
[    5.074934] dwc2 1e106000.usb: DWC OTG Controller
[    5.078228] dwc2 1e106000.usb: new USB bus registered, assigned bus number 2
[    5.085343] dwc2 1e106000.usb: irq 91, io mem 0x1e106000
[    5.092138] hub 2-0:1.0: USB hub found
[    5.094690] hub 2-0:1.0: 1 port detected
[    5.114686] usbcore: registered new interface driver usb-storage
[    5.121338] usbcore: registered new interface driver uas
[    5.125642] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.135993] init: - preinit -
[    6.055212] random: procd: uninitialized urandom read (4 bytes read)
[   10.306255] mount_root: loading kmods from internal overlay
[   10.362224] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   10.375663] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   10.819132] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 543
[   10.872303] UBIFS (ubi0:1): recovery needed
[   11.006866] UBIFS (ubi0:1): recovery completed
[   11.010234] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   11.017760] UBIFS (ubi0:1): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   11.027688] UBIFS (ubi0:1): FS size: 112379904 bytes (107 MiB, 871 LEBs), journal size 5677056 bytes (5 MiB, 44 LEBs)
[   11.038287] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[   11.044908] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID D02FE5E2-AF1B-48B3-8D4D-BEB09C323E0D, small LPT model
[   11.057405] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   11.066920] block: extroot: not configured
[   11.086938] UBIFS (ubi0:1): un-mount UBI device 0
[   11.090256] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[   11.127390] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 546
[   11.199291] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   11.205764] UBIFS (ubi0:1): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   11.215676] UBIFS (ubi0:1): FS size: 112379904 bytes (107 MiB, 871 LEBs), journal size 5677056 bytes (5 MiB, 44 LEBs)
[   11.226285] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[   11.232897] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID D02FE5E2-AF1B-48B3-8D4D-BEB09C323E0D, small LPT model
[   11.246686] mount_root: loading kmods from internal overlay
[   11.299599] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   11.307588] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   11.481743] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   11.490027] block: extroot: not configured
[   11.512552] mount_root: switching to ubifs overlay
[   11.576332] urandom-seed: Seeding with /etc/urandom.seed
[   11.731247] procd: - early -
[   11.732864] procd: - watchdog -
[   12.178770] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
[   12.427421] procd: - watchdog -
[   12.429763] procd: - ubus -
[   12.533002] random: ubusd: uninitialized urandom read (4 bytes read)
[   12.540504] random: ubusd: uninitialized urandom read (4 bytes read)
[   12.546156] random: ubusd: uninitialized urandom read (4 bytes read)
[   12.553830] procd: - init -
[   13.568595] kmodloader: loading kernel modules from /etc/modules.d/*
[   13.681841] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[   13.702434] NET: Registered protocol family 8
[   13.705487] NET: Registered protocol family 20
[   13.782502] tun: Universal TUN/TAP device driver, 1.6
[   13.795153] PPP generic driver version 2.4.2
[   13.815168] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.846174] Lantiq (VRX) DSL CPE MEI driver, version 1.5.17.6, (c) 2007-2015 Lantiq Beteiligungs-GmbH & Co. KG
[   13.864511] 
[   13.864511] 
[   13.864511] Lantiq CPE API Driver version: DSL CPE API V4.17.18.6
[   13.882217] 
[   13.882217] Predefined debug level: 3
[   13.915556] Loading modules backported from Linux version v4.19.98-0-gd183c8e2647a
[   13.921783] Backport generated by backports.git v4.19.98-1-0-g8204eb99
[   13.934764] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.946241] Infineon Technologies DEU driver version 2.0.0 
[   13.953287] IFX DEU DES initialized (multiblock).
[   13.958464] IFX DEU AES initialized (multiblock).
[   13.962712] IFX DEU ARC4 initialized (multiblock).
[   13.967048] IFX DEU SHA1 initialized.
[   13.970533] IFX DEU MD5 initialized.
[   13.974174] IFX DEU SHA1_HMAC initialized.
[   13.978408] IFX DEU MD5_HMAC initialized.
[   13.998310] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   14.068336] urngd: v1.0.2 started.
[   14.100721] NET: Registered protocol family 24
[   14.115213] usbcore: registered new interface driver ums-alauda
[   14.123502] usbcore: registered new interface driver ums-cypress
[   14.131821] usbcore: registered new interface driver ums-datafab
[   14.139908] usbcore: registered new interface driver ums-freecom
[   14.148222] usbcore: registered new interface driver ums-isd200
[   14.156580] usbcore: registered new interface driver ums-jumpshot
[   14.164706] usbcore: registered new interface driver ums-karma
[   14.173578] usbcore: registered new interface driver ums-sddr09
[   14.181875] usbcore: registered new interface driver ums-sddr55
[   14.190659] usbcore: registered new interface driver ums-usbat
[   14.198186] usbcore: registered new interface driver usblp
[   14.237897] xt_time: kernel timezone is -0000
[   14.395498] usbcore: registered new interface driver snd-usb-audio
[   14.431177] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   14.435671] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT3062.eeprom'.
[   14.447314] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3572, rev 0223 detected
[   14.453754] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
[   14.461726] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   14.475099] kmodloader: done loading kernel modules from /etc/modules.d/*
[   14.505000] random: crng init done
[   14.507027] random: 6 urandom warning(s) missed due to ratelimiting
[   29.184106] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   29.207753] device eth0 entered promiscuous mode
[   29.215360] br-lan: port 1(eth0.1) entered blocking state
[   29.219454] br-lan: port 1(eth0.1) entered disabled state
[   29.225475] device eth0.1 entered promiscuous mode
[   29.249701] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   29.316961] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   32.473327] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[   32.478510] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   32.492347] br-lan: port 1(eth0.1) entered blocking state
[   32.496386] br-lan: port 1(eth0.1) entered forwarding state
[   32.503113] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   32.509363] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   34.142406] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
[   34.189754] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.40
[   34.321732] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   34.359547] br-lan: port 2(wlan0) entered blocking state
[   34.363500] br-lan: port 2(wlan0) entered disabled state
[   34.369409] device wlan0 entered promiscuous mode
[   41.173141] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   41.178658] br-lan: port 2(wlan0) entered blocking state
[   41.183415] br-lan: port 2(wlan0) entered forwarding state